Blue Smart IP22 SLA/LiFePO4 12V 30A Single Charger BPC123047012

Blue Smart IP22 SLA/LiFePO4 Charger 12V 30A Single Output Fan Assisted BPC123047012 (AU/NZ Plug)

Important Information: All Batteries connected to this charger MUST be capable of a maximum charge rate of either 30 Amps or 15 Amps dependant on whether high or low current mode is selected. There is no individual charge cycle for each separate battery, therefore all batteries will follow the same charge cycle. As this charger contains an integrated FET battery isolator, it is therefore possible to charge three batteries with a single charger whilst keeping the batteries isolated. Charging current is divided among the batteries dependant on battery state of charge in combination with battery parameters and other circuit parameters. The charger, when connected to multiple batteries will raise the voltage of the lowest battery at the selected full current until it matches the second lowest battery voltage. At this point the available current is spread between these two batteries. When the voltage of the two batteries then matches the third battery the current is divided between the three batteries. All batteries will then reach absorption phase together and cycle together.

Replaces the BPC123042012

Important Information:

All Batteries connected to this charger MUST be capable of a maximum charge rate of either 30 Amps or 15 Amps dependant on whether high or low current mode is selected.

There is no individual charge cycle for each separate battery, therefore all batteries will follow the same charge cycle.

As this charger contains an integrated FET battery isolator, it is therefore possible to charge three batteries with a single charger whilst keeping the batteries isolated. Charging current is divided among the batteries dependant on battery state of charge in combination with battery parameters and other circuit parameters.

The charger, when connected to multiple batteries will raise the voltage of the lowest battery at the selected full current until it matches the second lowest battery voltage. At this point the available current is spread between these two batteries. When the voltage of the two batteries then matches the third battery the current is divided between the three batteries. All batteries will then reach absorption phase together and cycle together.

Important Information:

All Batteries connected to this charger MUST be capable of a maximum charge rate of either 30 Amps or 15 Amps dependant on whether high or low current mode is selected.

There is no individual charge cycle for each separate battery, therefore all batteries will follow the same charge cycle.

As this charger contains an integrated FET battery isolator, it is therefore possible to charge three batteries with a single charger whilst keeping the batteries isolated. Charging current is divided among the batteries dependant on battery state of charge in combination with battery parameters and other circuit parameters.

The charger, when connected to multiple batteries will raise the voltage of the lowest battery at the selected full current until it matches the second lowest battery voltage. At this point the available current is spread between these two batteries. When the voltage of the two batteries then matches the third battery the current is divided between the three batteries. All batteries will then reach absorption phase together and cycle together.

Replaces previous model – BPC123044012

Important Information:

All Batteries connected to this charger MUST be capable of a maximum charge rate of either 30 Amps or 15 Amps dependant on whether high or low current mode is selected.

There is no individual charge cycle for each separate battery, therefore all batteries will follow the same charge cycle.

As this charger contains an integrated FET battery isolator, it is therefore possible to charge three batteries with a single charger whilst keeping the batteries isolated. Charging current is divided among the batteries dependant on battery state of charge in combination with battery parameters and other circuit parameters.

The charger, when connected to multiple batteries will raise the voltage of the lowest battery at the selected full current until it matches the second lowest battery voltage. At this point the available current is spread between these two batteries. When the voltage of the two batteries then matches the third battery the current is divided between the three batteries. All batteries will then reach absorption phase together and cycle together.

Replaces previous model – BPC123044012

The Blue Smart IP22 Charger is the new professional battery charger with built-in Bluetooth.

The Blue Smart IP22 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans.

Bluetooth Smart
The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.

High efficiency
With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.

Adaptive 6-stage charge algorithm: test – bulk – absorption – recondition – float – storage
The Blue Smart Charger features a microprocessor controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.

Storage Mode: less maintenance and aging when the battery is not in use
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.

Also charges Li-ion (LiFePO₄) batteries
LiFePO₄ batteries are charged with a simple bulk – absorption – float algorithm.

NIGHT and LOW setting
When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.

Protected against overheating
Output current will reduce as temperature increases up to 50°C, but the Blue Smart Charger will not fail.

Eleven LEDs for status indication
Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY.
MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION.

Victron Energy IP22 Charger Manual

VictronConnect Compatible: VictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built in, or are connected to a VE.Direct Bluetooth Smart Dongle, or a VE.Direct to USB Interface Find out more about VictronConnect here, or download the App via these links.

40 Years Experience
SIMPOWER is at the forefront of battery technology. With 40 years of expertise and experience in research contracts, design and developing of both new technology cells and specialist industrial battery applications.

In other words from concept of cells to production manufacturing, SIMPOWER knows how to achieve customer satisfaction.

Own Manufacturing
SIMPOWER has its own manufacturing plant with state of the art welding and manufacturing equipment servicing all parts of New Zealand from the southern to northern end of the country with a quick efficient service. They offer free technical advice* on battery selection and pack design and have extensive technical advice.

SIMPOWER offers a unique facility and service of repacking battery packs for equipment which is no longer produced or perhaps difficult to source. Where possible they replace existing cells with increased capacity batteries to improved customers run time and service life if possible.

* Advice is free for the first 60 minutes, or part thereof. All subsequent advise will be billed at the SIMPOWER hourly rate or an agreed amount, subject to subsequent sales.

Exclusive
SIMPOWER has extensive knowledge and expertise of cells and battery pack build and is an exclusive distributor in NZ for SAFT, a world leader and innovator in cell technologies, as well as an approved distributor for PANASONIC, SENTRY, EVE, ARTS Energy and a supplier of FDK, DURACELL, Sonnenschein among others. SIMPOWER carries a wide range of many brands in stock and has the ability to source all leading brands from the global market place.

Contact us to discuss your requirements further.

With over 10,000 products to choose from ranging from battery packs, individual batteries and cells, to chargers, power supplies, analysers, Lutron meters and test equipment they have the widest range of battery products available in New Zealand. If they don’t have it they can find it for you.

Contact us to discuss your requirements further.